6' lance and raker bucking saw

Post here if you are trying to identify a saw, or want to discuss specific features of saws that can be used for identification.
soli
PostsCOLON 147
JoinedCOLON January 24th, 2013, 9:25 pm

6' lance and raker bucking saw

Post by soli » November 28th, 2018, 10:01 pm

Hoping to get some help ID'ing the saw on the right:
crosscut-ground-1a.jpg
It has lite angle grinder marks where an etching may have existed.

It's 1/4" or 5/16" longer than 72"
One end has nine lances, the other has eight
The width at the first gullet is about 2.5", and 4" to the tip of the 1.5" lance
The middle of the saw is 2.25" wider, or about 4.75" to the gullet and 6.25 to the tooth tip.
Crescent ground
One end has nine lances, the other has eight.

sandersdwa
PostsCOLON 41
JoinedCOLON January 11th, 2015, 6:53 pm

Re: 6' lance and raker bucking saw

Post by sandersdwa » November 29th, 2018, 12:14 pm

I'm going to guess a Craftsman Big Fir just to stimulate other feedback.
Do you have any faint etch left?
Measured one I just sharpened for a local cache and it measures .095" at the center raker and .090" at the outer rackers. .060" at the center back and .071 on the back opposite the outer rakers. Length is about 1/6 inch over 6 foot with 8 cutters on each end.

Here is the saw in the vise, it's faint etch, and a nice etch example.
Attachments
20181119_154543.jpg
20181129_114907.jpg
Picture1.jpg

Highway Bob
PostsCOLON 40
JoinedCOLON February 22nd, 2015, 8:08 pm
LocationCOLON Pittsburg, Kansas

Re: 6' lance and raker bucking saw

Post by Highway Bob » December 1st, 2018, 8:40 pm

Sandersdwa, NICE vise! 3 layers of 3/4" plywood per side? How clever for those of us that don't have access to anything but 1-1/2" lumber.

Highway Bob

User avatar
Jim_Thode
PostsCOLON 720
JoinedCOLON June 28th, 2012, 9:34 am
LocationCOLON Onalaska, Washington State, USA
CONTACTCOLON

Re: 6' lance and raker bucking saw

Post by Jim_Thode » December 2nd, 2018, 6:50 am

Highway Bob wroteCOLONSandersdwa, NICE vise! 3 layers of 3/4" plywood per side? How clever for those of us that don't have access to anything but 1-1/2" lumber.

Highway Bob
Looks like a microllam ( https://www.weyerhaeuser.com/woodproduc ... ollam-lvl/ ) and at least in the US, they should be available anyplace.


Image

sandersdwa
PostsCOLON 41
JoinedCOLON January 11th, 2015, 6:53 pm

Re: 6' lance and raker bucking saw

Post by sandersdwa » December 2nd, 2018, 8:24 am

Yes, Microlam as suggested by Dolly. Expensive but worth it because I no longer have warping due to conditions and very straight.

soli
PostsCOLON 147
JoinedCOLON January 24th, 2013, 9:25 pm

Re: 6' lance and raker bucking saw

Post by soli » December 7th, 2018, 5:27 am

sandersdwa wroteCOLONI'm going to guess a Craftsman Big Fir just to stimulate other feedback.
Do you have any faint etch left?
Measured one I just sharpened for a local cache and it measures .095" at the center raker and .090" at the outer rackers. .060" at the center back and .071 on the back opposite the outer rakers. Length is about 1/6 inch over 6 foot with 8 cutters on each end.
I'm not sure of the exact thicknesses. My micrometer is a plastic one branded Blum (hinge/hardware manufacturer) and was probably just bling at some trade show. But it's accurate enough that using it at different places on the blade indicates clearly that it was crescent ground.

The etch, if there ever was one, has been ground away for some reason. Here's a pick showing grinder marks:
crosscut-grinder-marks-1a.jpg

BUTTON_POST_REPLY